WS trapezoidal roof & wall sheets

One profile family for roofs, walls and ceilings

Trapezoidal sheets are the most widely used cladding for pre-engineered and industrial buildings. Deeper 5- and 6-rib profiles span further between purlins and girts; 7-, 9- and 11-rib profiles give a finer look for walls and smaller buildings; the shallow 13-rib profile is used for ceilings and liners.

Sheets are fixed through the crest or valley with self-drilling screws and sealing washers – see roof sheeting and wall sheeting.

WS trapezoidal profiles (1/2).

WS trapezoidal profiles (2/2).

Profiles and technical data

WS trapezoidal sheets
Code	Cover (mm)	Ribs	Rib (mm)	Thickness (mm)	Yield	Use
WS 1000-32-5	1000	5	32	0.40–0.60	–	Roof & wall
WS 1035-28-5	1035	5	28	0.35–0.60	–	Roof & wall
WS 900-39-6	900	6	39	0.40–0.60	G550	Wall
WS 1000-24-7	1000	7	24	0.35–0.60	–	Roof & wall
WS 1000-22-9	1000	9	22	0.35–0.60	–	Roof & wall
WS 920-22-9D	920	9	22	0.35–0.60	–	Roof
WS 940-23-11	940	11	23	0.35–0.60	G550	Roof & wall
WS 1085-9-13	1085	13	9	0.25–0.50	–	Ceiling & wall

Coil width for all trapezoidal profiles is 1200 mm. Spans depend on thickness, loads and the number of spans – ask for the span table of the selected profile.

Fixing and laps

Roof: fix through the crest with sealing washers; side lap one rib
Wall: fix through the valley; side lap one rib
End laps on roofs at least 150 mm with sealant, on walls 100 mm
Use foam closers at eaves and ridges

各市场标准与要求

World Steel 设计、加工本产品及编制文件所依据的规范——以及各市场的主要几何与荷载要求。

美国

ASTM A653 / A792Galvanized / 55 % Al-Zn coated sheet
ASTM A755Coil-coated (pre-painted) metallic-coated sheet
AISI S100Cold-formed steel design
ASTM E1592 · UL 580Wind uplift testing of roof panels

全部United States标准 →

澳大利亚 / 新西兰

AS 1397Metallic-coated steel sheet – G300 to G550, Z / AZ coatings
AS/NZS 2728Pre-finished / pre-painted sheet
AS 1562.1Design and installation of metal roof and wall cladding
AS 4040Methods of testing sheet roof and wall cladding (incl. cyclonic)

全部Australia & New Zealand标准 →

欧洲

EN 10346Continuously hot-dip coated steel flat products
EN 10169Organic coated (pre-painted) steel flat products
EN 14782Self-supporting metal sheet for roofing and cladding – CE marking
EN 1993-1-3Cold-formed members and sheeting

全部Europe标准 →

摘要仅供参考——以项目技术规格书、所采用的规范版本及主管机构要求为准。

表面处理

表面处理	标准 / 备注
Zinc-aluminium (AZ) coated	AZ100–AZ150 · AS 1397 / ASTM A792 / EN 10346
Galvanized (Z)	Z180–Z275 · AS 1397 / ASTM A653 / EN 10346
Pre-painted	Polyester or SMP paint system on AZ / Z substrate · AS/NZS 2728 / ASTM A755 / EN 10169
Colours	Standard colour range; special colours on minimum order quantity

常见问题

Which profile is best for a warehouse roof?

The deeper 5-rib profiles (WS 1000-32-5, WS 1035-28-5) span furthest between purlins and drain heavy rain best; finer profiles suit walls and small buildings.

Can the same profile be used for roof and wall?

Yes – most profiles are used for both; WS 900-39-6 is a wall profile and WS 1085-9-13 is for ceilings and liners.